Enerzone Solution 2.3 Specifikace

45189 ENERZONE E.P.A. WOOD STOVE MANUAL Solution 1.6 Solution 1.8 Solution 2.3 Solution 2.9 US ENVIRONMENTAL PROTECTION AGENCY PHASE II CERTIFIED

91.2 POSITIONING THE STOVE It is very important to position the wood stove in an area that will favour the most efficient heat distribution throug

10 Figure 1.3 Clearances to combustible materials

111.3.1 Reduced clearances using shielding You may decrease the minimum clearances to combustible materials by installing heat radiation shields be

121.4 FLOOR PROTECTOR If the stove is to be installed on top of a combustible floor, it must be guarded by a non-combustible material extending at l

13SECTION 2.0 CHIMNEY (FLUE SYSTEM) 2.1 DEFINITIONS For clarity, the following definitions should be used with respect to these instructions: •

14If you are using a masonry chimney, it is important that it be built in compliance with the specifications of the Building Code. It must be lined

15 FIGURE 2.2 Minimum Height of the Chimney 2.2.1 Step by step installation of your factory-built chimney The way to install your chimney may var

16Typical installation through the wall Wall support system If your chimney must rise along an outside wall, you need to connect it to your stove t

17Typical installation through the ceiling Ceiling support system If your chimney must rise inside the house and go through the ceiling, you need t

18 2.2.2 Typical installation through an existing masonry chimney You can also install your stove using your existing masonry chimney. To do so, f

1INTRODUCTION Stove Builder International, one of the most important wood stove and fireplace manufacturers in North America, congratulates you on y

19 FIGURE 2.2.2 (B) Factory Built Thimble

20 FIGURE 2.2.2 (C) Brick Thimble

212.3 CHIMNEY CONNECTOR Your chimney connector (commonly called stove pipe) and chimney must have the same diameter as the stove’s exhaust outlet. T

22 FIGURE 2.3 (A) Connecting Sections 1/4" RISE PER FOOT FIGURE 2.3 (B) Minimum Slope

232.4 DRAFT Your E.P.A Enerzone stove’s performance will be optimised if it is installed with a chimney (flue) system that provides an adequate dra

242.6 THE ADVANTAGE OF INSTALLING A BLOWER (FAN) A blower can be installed at the back of your E.P.A Enerzone stove. This option is necessary if y

25SECTION 3.0 OPERATION Keep these instructions for future reference. WARNING: • ANY MODIFICATION OF THE APPLIANCE THAT HAS NOT BEEN APPROVED I

263.1 SAFETY INFORMATION • These stoves are designed for safe operation WHEN BURNING WOOD ONLY. Altering or modifying the unit or installation w

27• Although the ceramic glass is extremely durable under any normal use, a few precautions are required. Do not attempt to push logs further into t

28 Wood species Energy yield (millions of BTU/cord) High energy yield Oak 29 Sugar Maple 28 Beech 26 Yellow birch 25 Ash 24 Elm 23 Medium energy y

2TABLE OF CONTENTS SECTION 1.0 INSTALLATION ... 4 1.1 GENERAL INSTALL

293.2.2 Simple wood moisture test Add one large piece of wood to the top of an established fire. If it starts to burn on three sides within one mi

30Intensity Draft Setting Low Push Control to end of travel. Medium Low Pull Control by 3/8” from closed position. Medium High Pull Control by 3/4

313.5 MAINTAINING THE FIRE Once the wood has been consumed (or partially consumed) and you have obtained a good bed of embers, you should reload th

32If the paint becomes scratched or damaged, it is possible to give your wood stove a brand new look, by repainting it with a 650oC heat resistant pa

33Glass specifications: Robax 5mm dimensions Solution 1.6 14 1/2" x 8 5/8" Solution 1.8 & 2.3

34• Clear the ashes from the area where the ash dump plug normally sits so that it will properly seat against the opening edges. Tap it down with yo

354.6 BAFFLE INSTALLATION 4.6.1 Baffle installation for Solution 1.6 model All firebrick and ceramic wool baffles must be properly in place for

364.6.2 Baffle installation for Solution 1.8 model All firebrick and ceramic wool baffles must be properly in place for correct burning operation

374.6.3 Baffle installation for Solution 2.3 model All firebrick and ceramic wool baffles must be properly in place for correct burning operation.

384.6.4 Baffle installation for Solution 2.9 model All firebrick and ceramic wool baffles must be properly in place for correct burning operatio

3SECTION 4.0 MAINTENANCE ... 31 4.1 CLEANING AND PAINTING YOUR STOVE ..

394.7 SECONDARY AIR TUBE REPLACEMENT (see Figure 4.11) 1. Remove cotter pin at RH end of tube. 2. Slide tube to left and lower tube end below RH p

40SECTION 5.0 SPECIFICATIONS 5.1 SOLUTION 1.6 Fuel Type Cordwood Test Standards ULC S627 (CSA B366.2) & UL 1482 residential.

415.2 SOLUTION 1.8 Fuel Type Cordwood Test Standards ULC S627 (CSA B366.2) & UL 1482 residential. Heat Output Maximum o

425.3 SOLUTION 2.3 Fuel Type Cordwood Test Standards ULC S627 (CSA B366.2) & UL 1482 residential. Heat Output Maximum o

435.4 SOLUTION 2.9 Fuel Type Cordwood Test Standards ULC S627 (CSA B366.2) & UL 1482 residential. Heat Output Maximum o

44ENERZONE LIMITED LIFETIME WARRANTY The warranty of the manufacturer extends only to the original consumer purchaser and is not transferable. This

4SECTION 1.0 INSTALLATION When installed and operated as described in these instructions, the E.P.A Enerzone wood stove is suitable for use as a f

51.1.1 Pedestal or leg kit assembly We suggest assembling the leg kit or pedestal before positioning the stove. See table 1.1.1 below: 1- Unscr

6 1.1.2 Installation of the decorative u-shaped inserts Your freestanding Enerzone wood stove is equipped with decorative u-shaped inserts. See ta

71.1.3 Door overlay installation In order to complete the assembly of your freestanding Enerzone wood stove, you need to install the door overlay.

81.1.4 Optional air mate installation Most freestanding Enerzone wood stoves can be equipped with an optional air mate. This device accumulates hea